Radio Type Approval, Homologation, Certification Services - Global Market Access Solutions
We can offer you reliably all services concerning Type Approval in Ukraine (Kiev). Our distinguished contact with the authority in Ukraine (Kiev), our good relationship to Ukrainian State Centre of Radio Frequencies (UCRF), Ukrmetrteststandard (UKRCSM), as well as the qualification in the homologation of consumer and automotive RF-products and Short Range Devices (SRD) in ISM-Frequency band will create your market access in Ukraine trouble-free and cost-effective.
We will assist you to put your product successfully on the market by offering the following services:
Identify applicable requirements for your specific product or technology feature to comply with current regulations in safety, EMC, wireless, etc.
Provide pre-compliance testing during the design and development phase to determine compliance
Assist in completion of applications and other required forms
Test in our accredited labs or your qualified facilities to issue CB Test Report and Certificate with applicable national differences and other test reports for wireless, etc.
Handle entire submittal process including working with local testing and certification organizations
Arrange for initial factory inspections that are required before certification issuance
Coordinate verification testing on qualified products as needed
Facilitate and expedite project progress with support of IB-Lenhardt AG local team and/or partner
Support renewal maintenance of certificates as needed
User manual translation service when needed
For Ukraine we can offer you a short termed tentative offer based upon a submitted Datasheet of the device: firstname.lastname@example.org
Marking of Certification Logo or Number Required?
Specific User Manual Requirements?
News for Ukraine
Ministry of Health issued Recommendations for Medical Devices
On 2020-01-22, the Ministry of Health published the Order “On Approving Methodological Recommendations on the Application of the Technical Regulation on Medical Devices"
Methodological recommendations about technical regulations on Medical Devices became effective in Ukraine. These recommendations were harmonized with the current MEDDEV guidance documents, clarifying technical regulations for various medical devices. These recommendations are not mandatory but should support companies in the medical sector to apply the technical regulations effectively.
June - The Ukrainian Cabinet of Ministers adopted the Resolution № 557 to amend Resolution № 139 namely the “Technical Regulations on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment” (Ukrainian RoHS).
The Resolution № 557 came into force on July 3, 2019 - these are the main points:
1. The Resolution excludes pipe organs product group from the scope.
2. The compliance deadline of July 1, 2019 has been removed for mercury in electric rotating connectors used in intravascular ultrasound imaging systems capable of high operating frequency (> 50 MHz).
3. The goal of the Resolution is to achieve compliance with the requirements of the EU RoHS Directives:
(EU) 2018/736 as regards an exemption for lead in glass or ceramic for some electrical components
(EU) 2018/737 as regards an exemption for lead in solders for the soldering to machined through hole discoidal and planar array ceramic multilayer capacitors
(EU) 2018/738 as regards an exemption for lead in cermet-based trimmer potentiometer elements
(EU) 2018/739 as regards an exemption for lead as an alloying element in steel
(EU) 2018/740 as regards an exemption for lead as an alloying element in aluminium
(EU) 2018/741 as regards an exemption for lead as an alloying element in copper
(EU) 2018/742 as regards an exemption for lead in high melting temperature solders
This amendment is based on the Directive (EU) 2017/2102 amending RoHS 2 Directive 2011/65/EU.
In accordance with the 3rd paragraph of the resolution of the Cabinet of Ministers of Ukraine as of 24.05.2017 N° 355 and its implementation until 31.12.2019, the technical regulations of radio equipment (TE RE) - approved by resolution of the Cabinet of Ministers of Ukraine dated 24.05.2017 N° 355 - DOES NOT apply to radio equipment installed and intended for use as a part of wheeled vehicles.
The Technical Regulation applies to radio equipment intended for use as a part of structure of wheeled vehicles, but not to installed parts on wheeled vehicles.
Conclusion; it only allpies to parts which available separately from vehicles.
If the radio equipment that is intended for use as a part of wheeled vehicles was implemented for use before 01.04.2018 and meets the requirements of the technical regulations for radio equipment and telecommunication end user (terminal) equipment approved by the resolution of the Cabinet of Ministers of Ukraine of 24.06.2009 N° 679, in that case the introduction into the market and the usage of such radio equipment is to be carried out without restrictions, provided that no changes have been done with regard to the structure and/or software that affects the essential requirements defined by paragraph 6-8 of the TR RE.
Where changes have been carried out, the manufacturer must carry out a conformity assessment of the radio equipment, in order to confirm its compliance with the essential requirements indicated in paragraph 6-8 of the TR RE.
Deadline EXTENDED until 31.12.2019
Ukraine has introduced amendments to the Resolution of the Cabinet of Ministers of Ukraine dated May 24, 2017 No. 355 "On Approval of the Technical Regulation of Radio Equipment".
Issued decree states that the DEADLINE for type approvals pursuant to the Technical Regulation of Radio Equipment has been extended until 31.12.2019 for vehicle components.
The additional paragraph states the following: To establish that until December 31, 2019, the operation of the Technical Regulation approved by this Resolution does not apply to radio equipment that is installed and intended for use as part of the construction of wheeled vehicles.
The amendment applies to vehicle radio equipments only and is valid for products which have already been approved pursuant to the previous RF TR.
Please be informed that according to the Ukrainian Technical Regulation (UA RED) the paragraph 25 states the following: Manufacturers must indicate their company's name, registered trade name or registered trademark and postal address at which they can be contacted, OR, if the size or nature of the radio equipment does not allow it, on the radio equipment package or in the accompanying document. Only one address shall be marked at which you can contact the manufacturer. Contact details are provided in accordance with the law on the application of languages.
The details in national language can be found in the Ukranian DoC which we prepare and provide to our customers for signature.
"To establish that before 2019-04-01 distribution and operation cannot be prohibited or limited due to reasons of non-compliance with the requirements of the Technical Regulation approved by this resolution, radio equipment, which
- was put into circulation before the date of entry into force of this resolution and
- meets the requirements of the Technical Regulation of Radio Equipment and Telecommunications Terminal Equipment, approved by the Resolution of the Cabinet of Ministers of Ukraine of June 24, 2009 No. 679 (Official Gazette of Ukraine, 2009, No. 50, item 1705), Technical Regulation on Electromagnetic Compatibility of Equipment , approved by the Decree of the Cabinet of Ministers of Ukraine dated December 16, 2015 No. 1077 (Official Gazette of Ukraine, 2016, No. 2, Article 72), Technical Regulations of Low Voltage Electric Equipment, approved by the Resolution of the Cabinet of Ministers of Ukraine id 16 December 2015 r. number 1067 (Official Bulletin of Ukraine, 2015 r., number 102, p. 3526). "
New Label Requirements
Ukraine’s Ministry of Economic Development and Trade confirmed the following new labelling format for radio equipment mandatory from 2017-09-01 onwards:
UA – stands for Ukraine
TR – provisional symbol of a Conformity Assessment Body (CAB) that is assigned to perform conformity assessment to the requirements of technical regulations
yyy - CAB ID number
Update on Conformity Declarations
The “Law of Ukraine No. 5312-VI”, released on 2012-11-29, contains the following news:
A Registration of Conformity Declarations in Ukraine is no longer required;
Declarations of Conformity issued in Ukraine for R&TTE, EMC, or Safety no longer require the registration by a CAB (Conformity Assessment Body);
It can now be replaced by a manufacturer's or his/her authorized representative's self-declaration.
The Type C electrical plug (or Europlug) is a two-wire plug that has two round pins. It fits into any socket that accepts 4.0 – 4.8 mm round contacts on 19 mm centres. They are being replaced by E, F, J, K or N sockets which work perfectly with Type C plugs. Type C plugs are generally limited for use in appliances that require 2.5 amps or less.
The Type F electrical plug (also known as a Schuko plug) has two 4.8 mm round pins spaced 19 mm apart. It is similar to the Type E plug but has two earth clips on the side rather than a female earth contact. The CEE 7/7 plug was developed to work with sockets E and F and has grounding clips on both sides (to work with Type F sockets) and a female contact (to accept the grounding pin of the type E socket). Type F plugs are rated 16 amps.